source: WorldVistAEHR/trunk/r/ORDER_ENTRY_RESULTS_REPORTING-OR-OCX--ORRC--ORRJ/ORWOD1.m@ 1375

ORWOD1  ; SLC/GSS - Utility for Order Dialogs ; 11/07/07 11:28am
        ;;3.0;ORDER ENTRY/RESULTS REPORTING;**243**;DEC 17, 1997;Build 242
        ;
NTRY    ;Entry point
        N TXT
        F NXTLINE=1:1 S TXT=$P($T(TXT+NXTLINE),";;",2) Q:TXT="Q"  S ^TMP("OR",$J,"MAIL",NXTLINE,0)=TXT
        Q
TXT     ;Text for report follows
        ;;         Quick Orders Which Should be Considered for Editing
        ;;
        ;;CPRS 27 has added three new fields (Route, IV Type, and Schedule) to the
        ;;IV Order Dialog. For all IV orders the Route and IV Type must be defined.
        ;;For Intermittent IV Type orders the schedule field must be defined. CPRS
        ;;will not process the orders unless these fields are defined.
        ;;
        ;;The following table of Quick Orders (QO) should be edited to add the new
        ;;field and data validation requirements implemented in CPRS GUI v27.  The
        ;;Quick Orders are listed in alphabetical order by QO name and include the
        ;;QO's IEN (internal reference number), display name, and Legend code.  The
        ;;Legend code corresponds to a letter or letters in the Legend (see below.)
        ;;You will need to evaluate each quick order and update it based on the
        ;;Legend code(s).
        ;;
        ;;A Quick Order can be edited by using the "Enter/edit quick orders" option
        ;;on the Order Menu Management menu in VistA (roll and scroll). At the
        ;;prompt, "Select QUICK ORDER NAME:", enter the name of the Quick Order.
        ;;The QO will then be displayed for your editing.  The "Enter/edit quick
        ;;orders" option can also be used to edit a Personal Quick Order.
        ;;
        ;;QO Edit Hint:
        ;;In addition to entering the QO name, users may also edit a Quick Order by
        ;;entering the back tick (`) and the IEN at the "Select QUICK ORDER NAME:"
        ;;prompt. For example, if the Quick Order name is PSI SICU CAM DOBUTAMINE 500
        ;;MG and the IEN is 6200, a user may enter "`6200" at the "Select QUICK ORDER
        ;;NAME:" prompt. This will the save time required to type the name of the Quick
        ;;Order in at the "Select QUICK ORDER NAME:" prompt.
        ;;
        ;;Note: The term 'null', as used below, can be viewed as meaning 'not defined'.
        ;;
        ;;Legend:
        ;;A...Problem: The IV type is null or the route is null.
        ;;    Action:  Please edit the IV Type or route fields with the appropriate
        ;;      information.
        ;;B...Problem: The IV type is 'I' and the schedule is null.
        ;;    Action:  For Intermittent IV Orders a schedule is needed to process the
        ;;      order.  Enter a schedule which denotes the Intermittent IV dose.
        ;;C...Problem: Continuous IV Type does not have a rate defined. When accepting
        ;;      the order in CPRS, rate is required adn must be between 1 and 9999.9,
        ;;      a whole number, or text that contains an '@'. Some continuous IV Type
        ;;      Quick Orders may not include a rate to allow provider to define at
        ;;      time of order.
        ;;    Action:  Evaluate need for rate default and assign in Quick Order if
        ;;      appropriate. The infusion rate must be a number up to four digits and
        ;;      it will allow up to one decimel place. If IV Type is not defined in
        ;;      the Quick Order, then an IV Type must be defined in the Quick Order
        ;;      set-up.
        ;;D...Problem:  The IV type is 'I' but the rate is not a whole number minute
        ;;      or hour yet not null.
        ;;    Action:  A valid "Infuse Over" value must be assigned to the Quick
        ;;      Order. Using the Quick Order Editor, add an "Infuse Over" value in
        ;;      the number of minutes (maximum of 9999).
        ;;E...Problem:  The IV limit or duration (limitation) value was other than
        ;;      null or a whole number.
        ;;    Action:  This field is not required but if it exists, it must be a
        ;;      whole number. To correct this, follow the Help Text for the Limitation
        ;;      Prompt in the Quick Order editor for this Quick Order.
        ;;F...Problem:  The Order Dialogs with 'MM' in the display text
        ;;    Action:  MMOL (millimole) has been added as a unit of measure.  Please 
        ;;      replace 'MM' with MMOL.
        ;;G...Problem:  Auto Accept Quick Order which was 'Y'es and now set to 'N'o.
        ;;    Action:  These Quick Orders were converted from an Auto Accept Quick
        ;;      Order to a non-Auto Accept Quick because they have at least one
        ;;      invalid field. Please correct the problems identified by the Legend
        ;;      code(s) for the Quick Order before setting the Quick Order back to
        ;;      an Auto-Accept Quick Order.
        ;;
        ;;Note: QO Names and QO Dislay Names over 30 characters are truncated at 30
        ;;      characters.  If in doubt on the Name you can use the IEN to edit the
        ;;      Quick Order (see above).
        ;;
        ;;                            -----------------------
        ;;                            
        ;;  IEN Name                           Display Name                   Legend
        ;;===== ============================== ============================== ======
        ;;Q