ORWOD1	; SLC/GSS - Utility for Order Dialogs ; 11/07/07 11:28am
	;;3.0;ORDER ENTRY/RESULTS REPORTING;**243**;DEC 17, 1997;Build 242
	;
NTRY	;Entry point
	N TXT
	F NXTLINE=1:1 S TXT=$P($T(TXT+NXTLINE),";;",2) Q:TXT="Q"  S ^TMP("OR",$J,"MAIL",NXTLINE,0)=TXT
	Q
TXT	;Text for report follows
	;;         Quick Orders Which Should be Considered for Editing
	;;
	;;CPRS 27 has added three new fields (Route, IV Type, and Schedule) to the
	;;IV Order Dialog. For all IV orders the Route and IV Type must be defined.
	;;For Intermittent IV Type orders the schedule field must be defined. CPRS
	;;will not process the orders unless these fields are defined.
	;;
	;;The following table of Quick Orders (QO) should be edited to add the new
	;;field and data validation requirements implemented in CPRS GUI v27.  The
	;;Quick Orders are listed in alphabetical order by QO name and include the
	;;QO's IEN (internal reference number), display name, and Legend code.  The
	;;Legend code corresponds to a letter or letters in the Legend (see below.)
	;;You will need to evaluate each quick order and update it based on the
	;;Legend code(s).
	;;
	;;A Quick Order can be edited by using the "Enter/edit quick orders" option
	;;on the Order Menu Management menu in VistA (roll and scroll). At the
	;;prompt, "Select QUICK ORDER NAME:", enter the name of the Quick Order.
	;;The QO will then be displayed for your editing.  The "Enter/edit quick
	;;orders" option can also be used to edit a Personal Quick Order.
	;;
	;;QO Edit Hint:
	;;In addition to entering the QO name, users may also edit a Quick Order by
	;;entering the back tick (`) and the IEN at the "Select QUICK ORDER NAME:"
	;;prompt. For example, if the Quick Order name is PSI SICU CAM DOBUTAMINE 500
	;;MG and the IEN is 6200, a user may enter "`6200" at the "Select QUICK ORDER
	;;NAME:" prompt. This will the save time required to type the name of the Quick
	;;Order in at the "Select QUICK ORDER NAME:" prompt.
	;;
	;;Note: The term 'null', as used below, can be viewed as meaning 'not defined'.
	;;
	;;Legend:
	;;A...Problem: The IV type is null or the route is null.
	;;    Action:  Please edit the IV Type or route fields with the appropriate
	;;      information.
	;;B...Problem: The IV type is 'I' and the schedule is null.
	;;    Action:  For Intermittent IV Orders a schedule is needed to process the
	;;      order.  Enter a schedule which denotes the Intermittent IV dose.
	;;C...Problem: Continuous IV Type does not have a rate defined. When accepting
	;;      the order in CPRS, rate is required adn must be between 1 and 9999.9,
	;;      a whole number, or text that contains an '@'. Some continuous IV Type
	;;      Quick Orders may not include a rate to allow provider to define at
	;;      time of order.
	;;    Action:  Evaluate need for rate default and assign in Quick Order if
	;;      appropriate. The infusion rate must be a number up to four digits and
	;;      it will allow up to one decimel place. If IV Type is not defined in
	;;      the Quick Order, then an IV Type must be defined in the Quick Order
	;;      set-up.
	;;D...Problem:  The IV type is 'I' but the rate is not a whole number minute
	;;      or hour yet not null.
	;;    Action:  A valid "Infuse Over" value must be assigned to the Quick
	;;      Order. Using the Quick Order Editor, add an "Infuse Over" value in
	;;      the number of minutes (maximum of 9999).
	;;E...Problem:  The IV limit or duration (limitation) value was other than
	;;      null or a whole number.
	;;    Action:  This field is not required but if it exists, it must be a
	;;      whole number. To correct this, follow the Help Text for the Limitation
	;;      Prompt in the Quick Order editor for this Quick Order.
	;;F...Problem:  The Order Dialogs with 'MM' in the display text
	;;    Action:  MMOL (millimole) has been added as a unit of measure.  Please 
	;;      replace 'MM' with MMOL.
	;;G...Problem:  Auto Accept Quick Order which was 'Y'es and now set to 'N'o.
	;;    Action:  These Quick Orders were converted from an Auto Accept Quick
	;;      Order to a non-Auto Accept Quick because they have at least one
	;;      invalid field. Please correct the problems identified by the Legend
	;;      code(s) for the Quick Order before setting the Quick Order back to
	;;      an Auto-Accept Quick Order.
	;;
	;;Note: QO Names and QO Dislay Names over 30 characters are truncated at 30
	;;      characters.  If in doubt on the Name you can use the IEN to edit the
	;;      Quick Order (see above).
	;;
	;;                            -----------------------
	;;                            
	;;  IEN Name                           Display Name                   Legend
	;;===== ============================== ============================== ======
	;;Q