Scheduling GUI User Manual

Welcome to the Scheduling GUI User Manual. This version reflects the software as of version 1.6. The software is liberally licensed under ​LGPL; this manual is licensed under ​CC BY. These licenses enable you to use and modify the software even in commercial settings.

Note: Information on system requirements, installation, and setup has been moved to the Scheduling GUI Technical Manual.

What is the Scheduling GUI?

Clinical Scheduling for Windows (BSDX) package is the Windows Extension of the PIMS Scheduling program in VISTA. It gives you many appointment management functions included in PIMS Scheduling, but with the added convenience and usability of a Graphic User Interface (GUI). The IHS Clinical Scheduling for Windows (BSDX) package should be used with PIMS Scheduling.

Getting Started

Before you launch the Clinical Scheduling package, double-check with your supervisor or Application Coordinator that the package has been properly installed and configured on your machine. Have your login information ready (you will use the same login information you use to access RPMS or VistA).

Login

To begin, select Clinical Scheduling using the Start menu or double-click the Clinical Scheduling desktop icon. This should bring up a splash screen and login dialog box. Enter your access and verify codes in the dialog box and click "OK." You should then see a window similar to the one below.

Initial view of the Clinical Scheduling application after logging in

If you encounter problems logging in, please consult your supervisor or Application Coordinator.

Terminology

Here are some key terms used in the software, and in this documentation.

Term	Description
Access Block	Color-coded blocks representing the time allotted for a specific Access Type (appointment). In the some places, they may be referred to as an Availability Blocks.
Access Types	Different kinds of appointments. Most clinics set up two Access Types: Scheduled and Walk-ins. In some places, Access Types may be referred to as Availability Types
Access Groups	Groups of Access Types. Clinics with only the two Access Types (Scheduled and Walk-ins) usually only have one Access Group containing both types. In clinics with a wider range of Access types, Access Groups make it easier to schedule and search for certain types of appointments.
Resources	Any person or service for which a patient can be scheduled. Resources can be physicians, diagnostic equipment (such as MRI, CT scan, ultrasound, and so on), or specialty appointment slots, such as physical therapy. Resources corresponds to what PIMS calls Clinics
Resource Groups	Resource Groups are categories of Resources that help to organize the variety of Resources available at each location. For example, a Resource Group of Dermatology can be used to group 3 different dermatology Resouces. In some places, Resource Groups may be called Departments.
Slot	Number of appointments per defined appointment length. For example: If SLOTS = 4 and your clinic (resource) appointment length is 30 minutes, then there are four (4) available appointments for every 30 minutes.

Clinic Display Area

The clinic schedule area is composed of date columns and time rows. Each column represents a day and each row represents a time interval. The time intervals can be 10, 15, 20, or 30 minutes. You can change the time interval using the View menu as long as the time interval is greater than the clinic default slot time. For more information about Time Scale, see the View Menu.

Access Blocks (areas of the schedule which are available for patient appointments) are indicated by the adjacent appointment times and dates. They may be color-coded to user preference. Different colors represent different Access Types. Position the cursor in such an area and click on the schedule display. The type of clinic access and the number of appointment slots available are visible in a message in the status bar at the bottom of the scheduling window. Clinic Access Types and colors can be defined and changed by the administrator of the scheduling package. (See Setting Up and Administering BSDX on for more information.) TODO: FIX THIS LINK.

Patient appointments are displayed on the schedule as white boxes containing a patient name and a note (if applicable).

Desktop showing patient appointments and multiple clinic schedules

Basic Screen Layout

The basic 5-day appointment screen is displayed below. At the far left is a menu tree view showing the Resources organized by Resource Group. In this case, the expanded view of Cardiology group shows three Resources. A Resource can be linked to a VISTA scheduling clinic so that when a patient has an appointment at that clinic and checks in, the PIMS encounter is checked in.

The colors on the schedule display correspond to various Access Types, set up for this Resource. The Resources, Resource Groups, Access Types, and colors can be customized to your individual clinic. You can create your own Access Types, Resource Groups using the Scheduling Management window. (See Using the Scheduling Management Window on page 54 for detailed instructions.) TODO: FIXME.

Basic Screen Layout

Table 2.2 describes the various items displayed on the basic screen layout.

Table 2.2: Descriptions of screen items

Screen Item	Description
Title Bar	Shows user ID and facility location in the upper left corner of the screen
Menu Bar	Appears below the Name and location of current user. The available text menus are: File, Appointment, View, and Help.
Resource Group Pane	Appears at the far left of the screen, below the menu bar. Displays the available Resources.
Times	Appears at the left side of the screen. Times are shown by hour and then by segment. They are listed in military time (for example 13:00 equals 1:00PM).
Resource Name	Appears in the upper left side of the screen, immediately above the “Times” column. Displays the name of the Resource currently active in the client window.
Client Window	Area on your screen that shows the work space for an application.
Appointment Date Selector	Appears in the upper right corner of the screen, below the Minimize, Maximize, and Exit buttons. The date selected is the starting date of the appointments currently displayed in the client window. The range of appointments displayed can be 1-day, 5-day, or 7-day.
Minimize, Maximize and Exit	Appears in the uppermost right corner of the screen. These buttons function just as they do in MS Windows applications.
Scroll Bars, Box, and Arrows	Appears at the far right side and at the bottom of the screen. These buttons function just as they do in MS Windows applications.
Colors	Displays Appointments using colors found in the Client Window area on the Schedule correspond to the various Access Types that can be set up for a particular provider.

Using the Resource Group Pane

The Resource Group Pane at the left-hand side of the screen lists both Resources and Resource Groups. If there is a plus sign (+), click it to expand the resource group to see all available resources. Click the minus sign (-) to collapse the group.

Dialog Boxes

Dialog boxes appear when the computer requires input from you or when an error occurs. In this manual, a dialog box is defined as any small box or screen that appears in front of the Scheduling interface and requests your attention or specific information. Most error dialog boxes ask you to click either OK or Cancel to acknowledge the error.

Changing the View

You can view the schedule in four modes: patients without appointments (walk-ins), 1-day, 5-day, or 7-day. The 1-day mode gives you maximum detail for a single day schedule. The 5-day and 7-day modes give you a view of five or seven days of the schedule from the selected date. Use the View menu shown in Figure 2-3 to change viewing modes.

Figure 2-3: View menu

1-Day View

Figure 2-4: Screen showing 1-Day view of schedule

5-Day View

Figure 2-5: Screen showing 5-Day view of schedule

7-Day View

Figure 2-6: Screen showing 7-Day view of schedule

Appointment Window

The appointment window shows the patient name, time of appointment, and notes. Figure 2-7 shows an appointment made for the 11:00-11:40 time slots for POCO REMUS. The patient selection is directly connected to VISTA. When an appointment is made, the appointment information is also stored in the VISTA scheduling package.

Figure 2-7: Appointment window & Resource Groups

Resource Group View

You can view an entire Resource Group’s schedule for one day. Figure 2-7 (above) shows that you can look at an entire group of Resources. In this case, the appointment window for the cardiology group is shown and all three Resource schedules for June 25th are displayed. You can also drag an appointment from one Resource to another or from one time slot to another. To view a Resource Group’s schedule:

1. Right Click a Resource Group.
2. Click Open Schedule. The Resource Group schedule shown in Figure 2-7 (above) is displayed.

Day to Day Use

Managing Appointments

Opening or Viewing a Schedule for a Selected Resource

To view the schedule for a selected Resource:

1. Select a Resource Group or individual Resource from the Resource Group pane. Expand and collapse the groups by clicking the plus sign (+) or minus sign (-) next to a group.
2. Do one of the following:
   • Double-click the Resource name and select Open Schedule from the File menu.
   • Right-click the Resource name and select Open Schedule from the Resource Group pane.

You can also view the schedule of all Resources in a group by selecting the group and then double-clicking the group name.

Finding an Available Appointment

You can search an entire Resource Group or specific Resource within a group for an available appointment using Find Available Appointment. To find an available appointment for a Resource Group or individual Resource:

1. Click the Resource Group or individual Resource within a group on the Resource Group pane for which you want to find the available appointment.
2. Do one of the following:
   • On the Appointment Menu, click Find Available Appointment.
   • Right-click on the Resource in the Resource Group pane, then click Find Available Appointment.
3. Select the search parameter using the options in the Search Parameters box.
   • In the Date Range box, select the range of dates in which you want to find an appointment. Click and drag the cursor from the beginning date to the ending date of the range. You can specify up to 14 consecutive days for your search.
   • In the Time of Day box, click AM Only, PM Only, or Both.
   • In the Day of the Week box, check the days of the week for which you want to find an appointment time.
   • In the Access Group box, select the appropriate Access Group from the drop-down list.
   • In the Access Type box, check all applicable Access Types for the appointment time you want to find.
4. Click Search when you have finished selecting your search parameters. A list of available appointments is displayed in the Search Result box. If there are not any appointments available for the parameters you selected, you will instead see a "no availability found" message box.

Searching for an available appointment (results)

If there are multiple appointments available, scroll through the results list to find the appointment you want. You can change the order of the list by clicking any column heading in the search results.

To select an appointment, double-click anywhere on the row for that appointment. When you select an appointment from the list, the Scheduling window opens to that date. You can now make the appointment, following the process outlined below.

Making an Appointment

To create a new patient appointment:

1. Click-and-hold over an area of the schedule that is available for appointments, and then drag the cursor to cover the entire time range needed for the appointment.
2. Do one of the following:
   • Click New Appointment from the Appointment menu.
   • Right-click on the selected area, then click the Add Appointment option.

You should see the Select Patient window below.

Making an appointment (steps 1-4)

3. Select a patient by typing lookup information (name, SSN, DOB, or HRN) in the Select Patient Search box. You may enter the first part of the patient's last name, the last 4 digits of the SSN, the entire SSN, HRN, or the DOB in the M-D-YYYY format.
4. Press Return or click Search. If the system finds only one match, the fields are automatically populated in the Select Patient field. If there is more than one match, a list of available patients is displayed. To select from this list, double-click the patient and then click OK to confirm your selection. Note: You can also recall the last patient you typed in this field by pressing the Spacebar and then Return.
5. Use the Patient Appointment dialog box to confirm the patient's contact information and to enter any relevant notes. The patient’s identification information shows in the Patient ID box, and the appointment information appears in the Appointment box. You can also click the Contact Information tab to view the patient’s contact information. The Contact Information tab is read-only; any changes made are not saved.
6. Click OK to enter this appointment in the schedule.

Editing Appointment Information

This feature allows you to edit information in an appointment, while keeping the appointment at the same time. Please see the next section for instructions on how to change the time of an appointment. To edit appointment information:

1. Select the appointment that you want to edit.
2. Do one of the following:
   • Right-click the appointment and then click Edit Appointment.
   • Choose Edit Appointment from the Appointment menu.

This should open the Patient Appointment dialog box.

3. Edit the appointment information as appropriate.

Changing Appointment Times

To change an appointment time:

1. Click-and hold the appointment box.
2. Drag the appointment to a new time slot. You can move appointments from one clinic to another by opening both clinic schedules, then clicking and dragging the appointment to the new time or Resource. This should call up a dialog box asking if you're sure you want to move the appointment.
3. Click Yes to confirm or No to cancel the move.

Viewing and Printing